martensitic transformation during compressive deformation

32 Comments

martensitic transformation during compressive deformation

Cited by 11Publish Year 2015Author Ying Qiu,Marcus L.Young,Xu NieMartensitic Phase Transformation and Deformation Behavior

The transformation between the face centered cubic austenitic and hexagonal closepacked martensitic phases during highpressure torsion processing was observed in a FeMnCAl twinninginduced plasticity steel.This phase transformation was not found in the same material processed by unidirectional compressive and tensile deformation.Cited by 1Publish Year 2015Author R.Kreethi,P.Sampark,Goutam Kumar Majhi,Krishna DuttaMartensitic Transformation During Compressive Deformation ·The martensitic transformation was the most difficult in the DRX grains because of the effect of small grain size.The tendency of transformation was decreased after compression at 1000 °C.Hot compression tests of a new high-Mn austenitic steel were carried out at deformation temperatures of 700,800,900,and 1000 °C under strain rate of 0 Cited by 4Publish Year 2018Author M.Eskandari,M.A.Mohtadi-Bonab,A.Zarei-Hanzaki,S.M.FatemiHigh Strain Rate Compression of Martensitic NiTi Shape Sep 22,2015·The compressive response of martensitic NiTi shape memory alloys (SMAs) under high strain rate (1200 s1) was investigated on a modified Kolsky (Split Hopkinson) compression bar.The single-loading momentum trapping system ensures precise deformation control (1.4,1.8,3.0,4.8,and 9.6 % strain) and single loading during dynamic compression.

Cited by 7Publish Year 2014Author Kun Yan,Dhriti Bhattacharyya,Qi Lian,Saurabh Kabra,Megumi Kawasaki,David G.Carr,Mark D.CallaSTRESS-INDUCED MARTENSITIC TRANSFORMATION OF

The two specimens exhibited identical deformation behaviour,both during initial loading,which was a stress-induced martensitic transformation process,and during subsequent cycling,which was a marten-site reorientation process.The cyclic deformation was terminated at g17% at t = 0 MPa for both samples.Figure 2(b) shows the shape recovery ofHigh strain rate deformation of martensitic NiTi shape In the present work,the mechanical behavior of a martensitic NiTi SMA under very high state rate (3 {times} 10{sup 3} s{sup {minus}1}) compression is obtained and is primarily compared to its low rate (3 {times} 10{sup {minus}4} s{sup {minus}1}) deformation behavior.In Situ TEM Observation on Martensitic Transformation Further study is necessary.Literature on martensitic transformation mechanism studied by in situ TEM has rarely been published.In this study,the martensitic transformation during tensile deformation in SUS304 stainless steel was observed directly by the in situ TEM technique.

Related searches for martensitic transformation during co

martensitic phase transformationaustenite to martensite transformationmartensitic phase12345NextStress-induced martensitic transformationoccurs during compressive deformation at ambient temperature,and the triggering stress shows an upward trend with increasing grain size,while the amount of martensite shows a downward trend.Author:Xinkai Ma,Xinkai Ma,Zhuo Chen,Lei Xiao,Wenjie Lu,Shifeng Luo,Yang MiPublish Year:2020Compressive deformation of a metastable titanium alloy Was this helpful?Martensitic Transformation During Compressive Deformation Sep 30,2015·Optical microscopy and x-ray diffraction (XRD) studies indicated martensitic phase transformation in the deformed specimens.The extent of phase transformation was determined by analyzing the XRD peaks using integrated intensity of the corresponding phases.The results are correlated with the extent of deformation in the respective samples.THE EFFECT OF REPEATED COMPRESSIVE DYNAMICosti.gov conference the effect of repeated compressive dynamic loading on the stress-induced martensitic transformation in niti shape memory alloys.the effect of repeated compressive dynamic loading on the stress-induced martensitic transformation in niti shape memory alloys.

The Influence of DeformationInduced Martensitic

Feb 01,2011·The strengthening behavior during deformation in the Cu 46.5 Zr 48.5 Al 5 alloy is ascribed to an austenitetomartensite phase transformation whereas the hardening and plasticity in Cu 50 Zr 50 were governed by the large amounts of twin boundaries and a deformationinduced phase transformation within the alreadyexisting martensitic phase.

Comments

  • hexagonal irregular steel pipe

    alloy steel seamless pipe - Precision Steel TubeTORICH Q235 S355jr ST52 inside hexagon hexagon oval ...

    More
  • z80 hot dipped gi roofing steel sheet supplier

    z80 steel sheet,z80 steel sheet Suppliers and offers 2,814 z80 steel sheet products.A wide variety ...

    More
  • china abs shipbuilding plate china abs shipbuilding plate

    China Abs Shipbuilding Plate,China Abs Shipbuilding Plate You can also choose from bending.As well a ...

    More

Leave a Message

Copyright © 2020.Ezir All rights reserved.